tag:blogger.com,1999:blog-2214461049219354662.post3555869733432573305..comments2024-03-28T13:08:35.581+04:00Comments on Physics Reference: Physics 9702 Doubts | Help Page 217Unknownnoreply@blogger.comBlogger8125tag:blogger.com,1999:blog-2214461049219354662.post-18594614764842772872019-05-06T22:02:39.259+04:002019-05-06T22:02:39.259+04:00because attenuation occurs (when Vout is greater t...because attenuation occurs (when Vout is greater than the supply voltage) and so, the output becomes 5.<br /><br />To prevent attenuation, there should be a very (very) little difference between the 2 inputs. Adminhttps://www.blogger.com/profile/03708185681043991662noreply@blogger.comtag:blogger.com,1999:blog-2214461049219354662.post-48365959641433522832019-05-06T12:46:50.979+04:002019-05-06T12:46:50.979+04:00For solution 1036 why are there no intermediate va...For solution 1036 why are there no intermediate values of Vout (as in a slope instead of a vertical line from -5 to +5)Anonymousnoreply@blogger.comtag:blogger.com,1999:blog-2214461049219354662.post-5860150652176791102019-03-07T22:07:21.854+04:002019-03-07T22:07:21.854+04:00The op-amp is saturated as the output is greater t...The op-amp is saturated as the output is greater than the input potential of ±5V. The output cannot be greater than the input. The output is either -5V or +5V (instead of an output greater than this value).Adminhttps://www.blogger.com/profile/03708185681043991662noreply@blogger.comtag:blogger.com,1999:blog-2214461049219354662.post-46979773053802860822019-03-07T19:57:51.658+04:002019-03-07T19:57:51.658+04:00Solution 1036 part C: How come the output voltage ...Solution 1036 part C: How come the output voltage is a bar graph? Anonymoushttps://www.blogger.com/profile/06258035524214109349noreply@blogger.comtag:blogger.com,1999:blog-2214461049219354662.post-64268155194499163072018-10-05T22:19:26.741+04:002018-10-05T22:19:26.741+04:00true. it has been corrected.true. it has been corrected.Adminhttps://www.blogger.com/profile/03708185681043991662noreply@blogger.comtag:blogger.com,1999:blog-2214461049219354662.post-18363914580218402362018-09-29T20:49:32.504+04:002018-09-29T20:49:32.504+04:00For Question 1037, the path difference should be 3...For Question 1037, the path difference should be 34-24=10cm instead of 32-24=10cmAnonymousnoreply@blogger.comtag:blogger.com,1999:blog-2214461049219354662.post-9106433607525414042016-05-16T16:59:23.318+04:002016-05-16T16:59:23.318+04:00the input (V_IN) is connected to V-.the input (V_IN) is connected to V-.Adminhttps://www.blogger.com/profile/03708185681043991662noreply@blogger.comtag:blogger.com,1999:blog-2214461049219354662.post-85089895402042084322016-05-15T17:27:14.878+04:002016-05-15T17:27:14.878+04:00Hello, In solution 1036 how do we know its an Inve...Hello, In solution 1036 how do we know its an Inverting Amp? Like for an Inverting dont we need resistors in the circuit like the whole Rf ordeal? :/ I have my cie tomorrow, i'd appreciate if you reply ASAPAnonymousnoreply@blogger.com